IC693CPU363-BE 90-30 系列PLC系统模块 CPU插槽

  GE Fanuc IC693CPU363是GE Fanuc系列90-3O PLC系统的一个模块。它连接到基板上的一个CPU插槽。这个CPU是80386X型的，速度是25兆赫兹。它使基板能够连接多达七个远程或扩展基板。它工作所需的电源是+5v直流和89OmA电流。它有一个电池来备份时钟，可以被覆盖。当它工作时，其温度在环境模式下可以从0度变化到60度。

GEFanuc IC693CPU363模块有三个端口。第一个端口支持电源连接器上的SNP或SNPX从机。另外两个端口支持SNP或SNP主机和从机，以及RTU从机。它还与RTU主机和CCM模块兼容。为了支持RTU主机，需要一个PCM模块。支持FIP、Profibus、GBC、GCM和GCM+模块的LAN端口也提供连接。它还支持多点。

GE Fanuc IC693CPU363模块的总用户存储器是240千字节，1千字节逻辑的典型扫描速率是0.22毫秒。它有2048个输入(%)和2048个输出(%Q点。CPU的离散全局内存(%G)为1280位。内部线圈(%M)占用4096位的空间，而输出或临时线罔(%T)使用256位。引用的系统状态(%S)使用128位。

寄存器存储器(%R)可通过Logicmaster或Control v2.2进行配置。Logicmaster以128个字为增量配置GE Fanuc IC693CPU363模块存储器，最多可达16，384个字。Control v2.2可以进行相同的配置，部署多达32，640个字。模拟输入(%A)和输出(%Q)可以像寄存器存储器—样使用相同的程序进行配置。GE Fanuc IC693CPU363的系统寄存器由28个字组成。

The GE Fanuc IC693CPU363 is a module of the GE Fanuc series 90-3O PLC system. It is connected to a CPU slot on the substrate. This CPU is a model 80386X with a speed of 25 megahertz. It enables the substrate to connect up to seven remote or extended substrates. The power supply required for its operation is +5v DC and 89OmA current. It has a battery to back up the clock and can be overwritten. When it works, its temperature can vary from 0 degrees to 60 degrees in ambient mode.

The GEFanuc IC693CPU363 module has three ports. The first port supports SNP or SNPX slaves on the power connector. The other two ports support SNP or SNP host and slave, as well as RTU slave. It is also compatible with RTU hosts and CCM modules. To support the RTU host, a PCM module is required. LAN ports that support FIP, Profibus, GBC, GCM, and GCM+ modules also provide connectivity. It also supports multiple points.

The total user memory of the GE Fanuc IC693CPU363 module is 240 kilobytes, and the typical scan rate for 1 kilobyte logic is 0.22 ms. It has 2048 inputs (%) and 2048 outputs (%Q points). The discrete global memory (%G) of the CPU is 1280 bits. The internal coil (%M) takes up 4096 bits of space, while the output or temporary wire (%T) uses 256 bits. The referenced system state (%S) uses 128 bits.

Register memory (%R) can be configured via Logicmaster or Control v2.2. Logicmaster is configured with GE Fanuc IC693CPU363 module memory in 128-word increments, up to 16,384 words. Control v2.2 can perform the same configuration, deploying up to 32,640 words. Analog inputs (%A) and outputs (%Q) can be configured using the same program as register memory. The GE Fanuc IC693CPU363 system register consists of 28 words.

服务:

*我们在专业的客户服务和售后团队方面投入了大量资金，让说母语的客户和专职服务人员无障碍交流。*零件涵盖100+厂家产品作为高品质自动化和控制组件的全球供应商，

*我们提供广泛的产品目录。

*以确保工业机械以高效和具有成本效益的方式恢复和运行。

*包括100多家世界领先的自动化控制设备的零部件制造商，其中许多可以在同—天或第二天交付。

联系人;

罗经理

邮箱: 3248602330@qq.com

QQ: 3248602330

电话/微信:+86-18030183032